Car Dismantling Shear
Feature
Application: only applicable to all types of scrapped cars. Our car dismantling shear is widely used in the scrap car recycling and disassembly industry and the field of renewable resources, mechanized disassembly can replace a large number of manual, the operation is safe, efficient, environmental protection,and saving,.One small car is disassembled for only 5 minutes, medium and large bus are usually disassembled for only 30 minutes, which is 10 times than the manual. Feature: (1) The knife body is made of height NM 400, long-wear-resistant, and other structural parts are made of Q345B manganese plate,High strength and strong toughness. (2) Special material customized blade can be used alternately on all sides, high wear resistance and strong utilization rate greatly reduce the replacement cost of vulnerable parts. (3) Reasonable closed structure design reinforced cylinder greatly improve the shear tear force to avoid collision cylinder damage oil leakage. (4) Advanced integrated circuit control system makes operators easier to operate with sensitive action,which improves the efficiency of disassembly. (5) The large displacement rotary device with closed-loop design has high torque and high stability, which makes the whole machine has superior service life and low safe and efficient late maintenance cos. Note: The car dismantling should try to avoid load rotation, do not do rotation action when tearing! Clamp arm (1) Made of altitude manganese plate, lightweight design, high strength and toughness to meet all kinds of harsh disassembly conditions. (2) Advanced integrated valve block hydraulic oil road design has convenient installation and maintenance action, sensitive clamp tension does not drop the cylinder. (3) Advanced reinforced cylinder design lifts high, opening degree meets the requirements of various types of vehicles. (4) It adopts the detachable type design. Our car dismantling shear can achieve accurate and easy tear of scrapped cars with the large displacement and large torque rotating motor, jaw opening reaches 850mm,slender body is particularly good at fine demolition ,easy stripping of the plastic ,wire and seats,etc.The car shear sheet can easily cut the car girder and ABC column with a thickness of less than 20 mm .The excavator clamp arm can fix and clamp the scrapped cars and make the disassembly more efficient ,it can be lifted up to 2meters high ,open size for 3,287 mm.The excavator clamp arm can achieve the tension and lower pressure action,the bowl-shaped fixture can be fixed and disassembled quickly ,all the oil cylinders adopt the closed design ,which is not easy to collide and damage,In addition, the customer has the lifting and lowering action of the pressure frame for choice, high structural strength, flexible action control.| excavator clamp arm | |||
| item/model | unit | ET06 | ET08 |
| weight | kg | 2160 | 4200 |
| suitable excavator | ton | 12-18 | 20-35 |
| activity height | mm | 1800 | 2200 |
| swing height | mm | 0 | 0 |
| open(max) | mm | 2860 | 3287 |
| open(min) | mm | 880 | 1072 |
| length | mm | 4650 | 5500 |
| height | mm | 1000 | 1100 |
| width | mm | 2150 | 2772 |
| there are two kinds of options: one is four movements (can achieve tension, clamping, up, and down) and the other is two movements (only up and down)。 | |||
| car dismantling shear | ||||||
| item/model | unit | ET04 | ET06 | ET08 | ||
| suitable excavator | ton | 6-10 | 12-16 | 20-35 | ||
| weight | kg | 410 | 1000 | 1900 | ||
| opening with jaw | mm | 420 | 770 | 850 | ||
| overall length | mm | 1471 | 2230 | 2565 | ||
| blade length | mm | 230 | 440 | 457 | ||
| maximum cutting force(blade middle) | ton | 45 | 60 | 80 | ||
| driving pressure | kgf/cm2 | 180 | 210 | 260 | ||
| driving flow | l/min | 50-130 | 100-180 | 180-230 | ||
| hydraulic rotation motor | motor set up pressure | kgf/cm2 | 150 | 150 | 150 | |
| motor oil volume | motor flux | l/min | 30-35 | 36-40 | 36-40 | |
